Additionally, accept a "now" timestamp, to allow avoiding rescans for keys
which are known never to have been used.
Note that the behavior when "now" is specified is slightly different than the
previous behavior when no timestamp was specified at all. Previously, when no
timestamp was specified, it would avoid rescanning during the importmulti call,
but set the key's nCreateTime value to 1, which would not prevent future block
reads in later ScanForWalletTransactions calls. With this change, passing a
"now" timestamp will set the key's nCreateTime to the current block time
instead of 1.
Fixes#9491
Minimum boost version was bumped to 1.47.0 in #8920, which
means the configure step won't even pass with older boost.
This version has boost filesystem v3, which means the
(crappy) fallbacks for older versions can go.
Preserve comment, order form, and account strings from the original wallet
transaction. Also set fTimeReceivedIsTxTime and fFromMe fields for consistency
with CWallet::CreateTransaction. The latter two fields don't influence current
wallet behavior, but do record that the transaction originated in the wallet
instead of coming from the network or sendrawtransaction.
More accurate than simply adding one byte per input, and properly handles the
case where the original transaction happened to have very small signatures
The result value indicates the actual fee on the transaction that was replaced. But there is an error message which uses the description 'oldfee' to refer to the original fee rate applied to the new transaction's estimated max size. It was confusing that two different uses of 'oldfee' had two different numeric values.
Have wallet's default bump value be higher than the default incrementalRelayFee to future proof against changes to incremental relay fee. Only applies when not setting the fee rate directly.
Use the wallet's fee calculation logic to properly clamp fee against minimums and maximums when calculating the fee for a bumpfee transaction. Unless totalFee is explictly given, in which case, manually check against min, but do nothing to adjust given fee.
In all cases do a final check against maxTxFee (after adding any incremental amount).
This command allows a user to increase the fee on a wallet transaction T, creating a "bumper" transaction B.
T must signal that it is BIP-125 replaceable.
T's change output is decremented to pay the additional fee. (B will not add inputs to T.)
T cannot have any descendant transactions.
Once B bumps T, neither T nor B's outputs can be spent until either T or (more likely) B is mined.
Includes code by @jonasschnelli and @ryanofsky
In spite of the name FindLatestBefore used std::lower_bound to try
to find the earliest block with a nTime greater or equal to the
the requested value. But lower_bound uses bisection and requires
the input to be ordered with respect to the comparison operation.
Block times are not well ordered.
I don't know what lower_bound is permitted to do when the data
is not sufficiently ordered, but it's probably not good.
(I could construct an implementation which would infinite loop...)
To resolve the issue this commit introduces a maximum-so-far to the
block indexes and searches that.
For clarity the function is renamed to reflect what it actually does.
An issue that remains is that there is no grace period in importmulti:
If a address is created at time T and a send is immediately broadcast
and included by a miner with a slow clock there may not yet have been
any block with at least time T.
The normal rescan has a grace period of 7200 seconds, but importmulti
does not.
On repeated calls to SelectCoins we try to meet the fee necessary for the last transaction, the new fee required might be smaller, so increase our change by the difference if we can.
Once we've picked coins and dummy-signed the transaction to calculate fee, if we don't have sufficient fee, then try to meet the fee by reducing change before resorting to picking new coins.
Performing signing in the inner loop has terrible performance
when many passes through are needed to complete the selection.
Signing before the algorithm is complete also gets in the way
of correctly setting the fee (e.g. preventing over-payment when
the fee required goes down on the final selection.)
Use of the dummy might overpay on the signatures by a couple bytes
in uncommon cases where the signatures' DER encoding is smaller
than the dummy: Who cares?
The meaning is clear from the context, and we're inconsistent here.
Also save typing when using named arguments.
- `bitcoinaddress` -> `address`
- `bitcoinprivkey` -> `privkey`
- `bitcoinpubkey` -> `pubkey`
Fee estimation can just check its own mapMemPoolTxs to determine the same information. Note that now fee estimation for block processing must happen before those transactions are removed, but this shoudl be a speedup.
Russell Yanofsky