i2pd configuration ================== i2pd can be configured via either command-line arguments or config files. Modifying `i2pd.conf` is just a way of passing command line arguments to i2pd at boot; for example, running i2pd with argument `--port=10123` and setting option `port = 10123` in config file will have the same effect. There are two separate config files: `i2pd.conf` and `tunnels.conf`. `i2pd.conf` is the main configuration file, where you configure all options. `tunnels.conf` is the tunnel configuration file, where you configure I2P hidden services and client tunnels. the `tunnels.conf` options are documented [here](tunnels.md). `i2pd.conf` accepts INI-like syntax, such as the following : = . Comments are "#", not ";" as you might expect. See [boost ticket](https://svn.boost.org/trac/boost/ticket/808) All command-line parameters are allowed as keys, but for those which contains dot (.), there is a special syntax. For example: i2pd.conf: # comment log = true # use stdout (default) ipv6 = true # settings for specific module [httpproxy] port = 4444 # ^^ this will be --httproxy.port= in cmdline # another comment [sam] enabled = true You are also encouraged to see the commented config with examples of all options in ``contrib/i2pd.conf``. Options specified on the command line take precedence over those in the config file. If you are upgrading your very old router (< 2.3.0) see also [this](config_opts_after_2.3.0.md) page. Available options ----------------- Run `./i2pd --help` to show builtin help message (default value of option will be shown in braces) ### General options Option | Description -------------------------------------- | -------------------------------------- conf | Config file (default: ~/.i2pd/i2pd.conf or /var/lib/i2pd/i2pd.conf). This parameter will be silently ignored if the specified config file does not exist. tunconf | Tunnels config file (default: ~/.i2pd/tunnels.conf or /var/lib/i2pd/tunnels.conf) pidfile | Where to write pidfile (default: i2pd.pid, not used in Windows) log | Logs destination: stdout, file, syslog (stdout if not set or invalid) (if daemon, stdout/unspecified are replaced by file in some cases) logfile | Path to logfile (default - autodetect) loglevel | Log messages above this level (debug, info, warn, error, none; default - warn) logclftime | Write full CLF-formatted date and time to log (default: false (write only time)) datadir | Path to storage of i2pd data (RouterInfos, destinations keys, peer profiles, etc ...) host | Router external IP for incoming connections (default: auto if SSU2 is enabled) port | Port to listen for incoming connections (default: auto (random)) daemon | Router will go to background after start (default: true) service | Router will use system folders like '/var/lib/i2pd' (on unix) or 'C:\ProgramData\i2pd' (on Windows). Ignored on MacOS and Android (default: false) ifname | Network interface to bind to ifname4 | Network interface to bind to for IPv4 ifname6 | Network interface to bind to for IPv6 address4 | Local address to bind to for IPv4 address6 | Local address to bind to for clearnet IPv6 nat | If true, assume we are behind NAT (default: true) ipv4 | Enable communication through IPv4 (default: true) ipv6 | Enable communication through clearnet IPv6 (default: false) notransit | Router will not accept transit tunnels, disabling transit traffic completely (default: false) floodfill | Router will be floodfill (default: false) bandwidth | Bandwidth limit: integer in KBps or letters: L (32), O (256), P (2048), X (unlimited). share | Max % of bandwidth limit for transit. 0-100 (default: 100) family | Name of a family, router belongs to netid | Network ID, router belongs to. Main I2P is 2. #### Notes `datadir` and `service` options are only used as arguments for i2pd, these options have no effect when set in `i2pd.conf`. ### NTCP2 Option | Description -------------------------------------- | -------------------------------------- ntcp2.enabled | Enable NTCP2 (default: true) ntcp2.published | Enable incoming NTCP2 connections (default: true) ntcp2.port | Port to listen for incoming NTCP2 connections (default: auto - port from general section) ntcp2.addressv6 | External IPv6 for incoming connections ntcp2.proxy | Specify proxy server for NTCP2. Should be http://address:port or socks://address:port ### SSU2 Option | Description -------------------------------------- | -------------------------------------- ssu2.enabled | Enable SSU2 (default: true) ssu2.published | Enable incoming SSU2 connections. (default: true) ssu2.port | Port to listen for incoming SSU2 connections (default: auto - 'port' from general section) ssu2.proxy | Specify UDP socks5 proxy server for NTCP2. Should be socks://address:port ssu2.mtu4 | MTU for local ipv4. (default: auto) ssu2.mtu6 | MTU for local ipv6. (default: auto) All options below still possible in cmdline, but better write it in config file: ### HTTP webconsole Option | Description -------------------------------------- | -------------------------------------- http.enabled | If webconsole is enabled. (default: true) http.address | The address to listen on (HTTP server) http.port | The port to listen on (HTTP server) (default: 7070) http.auth | Enable basic HTTP auth for webconsole (default: false) http.user | Username for basic auth (default: i2pd) http.pass | Password for basic auth (default: random, see logs) http.strictheaders | Enable strict host checking on WebUI. (default: true) http.hostname | Expected hostname for WebUI (default: localhost) ### HTTP proxy Option | Description -------------------------------------- | -------------------------------------- httpproxy.enabled | If HTTP proxy is enabled. (default: true) httpproxy.address | The address to listen on (HTTP Proxy) httpproxy.port | The port to listen on (HTTP Proxy) (default: 4444) httpproxy.addresshelper | Enable address helper (jump). (default: true) httpproxy.keys | Optional keys file for HTTP proxy local destination httpproxy.signaturetype | Signature type for new keys if keys file is set. (default: 7) httpproxy.inbound.length | Inbound tunnels length if keys is set. (default: 3) httpproxy.inbound.quantity | Inbound tunnels quantity if keys is set. (default: 5) httpproxy.inbound.lengthVariance | Inbound tunnels length variance if keys is set. (default: 0) httpproxy.outbound.length | Outbound tunnels length if keys is set. (default: 3) httpproxy.outbound.quantity | Outbound tunnels quantity if keys is set. (default: 5) httpproxy.outbound.lengthVariance | Outbound tunnels length variance if keys is set. (default: 0) httpproxy.outproxy | HTTP proxy upstream out proxy url (like http://false.i2p) httpproxy.i2cp.leaseSetType | Type of LeaseSet to be sent. 1, 3 or 5. (default: 3) httpproxy.i2cp.leaseSetEncType | Comma separated encryption types to be used in LeaseSet type 3 or 5 ### Socks proxy Option | Description -------------------------------------- | -------------------------------------- socksproxy.enabled | If SOCKS proxy is enabled. (default: true) socksproxy.address | The address to listen on (SOCKS Proxy) socksproxy.port | The port to listen on (SOCKS Proxy). (default: 4447) socksproxy.keys | Optional keys file for SOCKS proxy local destination socksproxy.signaturetype | Signature type for new keys if keys file is set. (default: 7) socksproxy.inbound.length | Inbound tunnels length if keys is set. (default: 3) socksproxy.inbound.quantity | Inbound tunnels quantity if keys is set. (default: 5) socksproxy.inbound.lengthVariance | Inbound tunnels length variance if keys is set. (default: 0) socksproxy.outbound.length | Outbound tunnels length if keys is set. (default: 3) socksproxy.outbound.quantity | Outbound tunnels quantity if keys is set. (default: 5) socksproxy.outbound.lengthVariance | Outbound tunnels length variance if keys is set. (default: 0) socksproxy.outproxy.enabled | Enable or disable SOCKS outproxy. (default: false) socksproxy.outproxy | Address of outproxy. Requests outside I2P will go there. socksproxy.outproxyport | Outproxy remote port socksproxy.i2cp.leaseSetType | Type of LeaseSet to be sent. 1, 3 or 5. (default: 3) socksproxy.i2cp.leaseSetEncType | Comma separated encryption types to be used in LeaseSet type 3 or 5 ### SAM interface Option | Description -------------------------------------- | -------------------------------------- sam.enabled | If SAM is enabled. (default: true) sam.address | The address to listen on (SAM bridge) sam.port | Port of SAM bridge. Usually 7656. SAM is off if not specified sam.singlethread | If false every SAM session runs in own thread. (default: true) ### BOB interface Option | Description -------------------------------------- | -------------------------------------- bob.enabled | If BOB is enabled. (default: false) bob.address | The address to listen on (BOB command channel) bob.port | Port of BOB command channel. Usually 2827. BOB is off if not specified ### I2CP interface Option | Description -------------------------------------- | -------------------------------------- i2cp.enabled | If I2CP is enabled. (default: true) i2cp.address | The address to listen on or an abstract address for Android LocalSocket i2cp.port | Port of I2CP server. Usually 7654. Ignored for Andorid i2cp.singlethread | If false every I2CP session runs in own thread. (default: true) ### I2PControl interface Option | Description -------------------------------------- | -------------------------------------- i2pcontrol.enabled | If I2P control is enabled. (default: false) i2pcontrol.address | The address to listen on (I2P control service) i2pcontrol.port | Port of I2P control service. Usually 7650. I2PControl is off if not specified i2pcontrol.password | I2P control authentication password. (default: itoopie) i2pcontrol.cert | I2P control HTTPS certificate file name. (default: i2pcontrol.crt.pem) i2pcontrol.key | I2P control HTTPS certificate key file name. (default: i2pcontrol.key.pem) ### UPNP Option | Description -------------------------------------- | -------------------------------------- upnp.enabled | Enable or disable UPnP, false by default for CLI and true for GUI (Windows, Android) upnp.name | Name i2pd appears in UPnP forwardings list. (default: I2Pd) ### Cryptography Option | Description -------------------------------------- | -------------------------------------- precomputation.elgamal | Use ElGamal precomputated tables. (default: false for x86-64 and true for other platforms) ### Reseeding Option | Description -------------------------------------- | -------------------------------------- reseed.verify | Verify .su3 signature. (default: false) reseed.urls | Reseed URLs, separated by comma reseed.yggurls | Reseed Yggdrasil's URLs, separated by comma reseed.file | Path to local .su3 file or HTTPS URL to reseed from reseed.zipfile | Path to local .zip file to reseed from reseed.threshold | Minimum number of known routers before requesting reseed. (default: 25) reseed.proxy | Url for https/socks reseed proxy ### Addressbook options Option | Description -------------------------------------- | -------------------------------------- addressbook.defaulturl | AddressBook subscription URL. Only used to initialize the AddressBook. addressbook.subscriptions | AddressBook subscriptions URLs, separated by comma. Note that defaulturl is not added to subscriptions URLs addressbook.hostsfile | File to dump AddressesBook in hosts.txt format ### Limits Option | Description -------------------------------------- | -------------------------------------- limits.transittunnels | Override maximum number of transit tunnels. (default: 5000) limits.openfiles | Limit number of open file descriptors (default: 0 - use system limit) limits.coresize | Maximum size of corefile in Kb (default: 0 - use system limit) ### Trust options Option | Description -------------------------------------- | -------------------------------------- trust.enabled | Enable explicit trust options. (default: false) trust.family | Make direct I2P connections only to routers in specified Family. trust.routers | Make direct I2P connections only to routers specified here. Comma separated list of base64 identities. trust.hidden | Should we hide our router from other routers? (default: false) ### Exploratory tunnels Option | Description -------------------------------------- | -------------------------------------- exploratory.inbound.length | Exploratory inbound tunnels length. (default: 2) exploratory.inbound.quantity | Exploratory inbound tunnels quantity. (default: 3) exploratory.outbound.length | Exploratory outbound tunnels length. (default: 2) exploratory.outbound.quantity | Exploratory outbound tunnels quantity. (default: 3) ### Time sync Option | Description -------------------------------------- | -------------------------------------- nettime.enabled | Enable NTP sync. (default: false) nettime.ntpservers | Comma-separated list of NTP server. (default: pool.ntp.org) nettime.ntpsyncinterval | NTP time sync interval in hours. (default: 72) ### Network information persist Option | Description -------------------------------------- | -------------------------------------- persist.profiles | Enable peer profile persisting to disk. (default: true) ### Meshnets transports Option | Description -------------------------------------- | -------------------------------------- meshnets.yggdrasil | Support transports through the Yggdrasil (default: false) meshnets.yggaddress | Local Yggdrasil's address to publish ### Windows-specific options Option | Description -------------------------------------- | -------------------------------------- insomnia | Prevent system from sleeping close | Action on close: minimize, exit, ask ### UNIX-specific options Option | Description -------------------------------------- | -------------------------------------- unix.handle_sigtstp | Handle SIGTSTP and SIGCONT signals. (default: false) `handle_sigtstp` enables handling of SIGTSTP and SIGCONT signals (*since 2.43.0*). SIGTSTP can be called using Ctrl+Z in terminal with running i2pd in it or by `kill` command. When signal recveived, i2pd will switch to offline mode and stop sending traffic and cleaning of netDb. All active tunnels will be frozen. To restore network connectivity you need to send SIGCONT signal to the proccess. Tunnels will be cleared if they should expire during the frozen state and new ones will be built. Local addressbook ----------------- There is also a special addressbook config file in the working directory at `addressbook/local.csv`. It lets your routers to work as a resolver for 3ld domains if you run that 2ld address on your router and it' presented in addressbook. Only i2pd can resolve such addresses, by sending special datagram requests.