I2P: End-to-End encrypted and anonymous Internet https://i2pd.website/
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
 
 
 
 
 

4.6 KiB

i2pd configuration

Command line options

  • --conf= - Config file (default: ~/.i2pd/i2p.conf or /var/lib/i2pd/i2p.conf) This parameter will be silently ignored if the specified config file does not exist. Options specified on the command line take precedence over those in the config file.

  • --tunconf= - Tunnels Config file (default: ~/.i2pd/tunnels.cfg or /var/lib/i2pd/tunnels.cfg)

  • --pidfile= - Where to write pidfile (dont write by default)

  • --log - Enable or disable logging to file. 1 for yes, 0 for no.

  • --loglevel= - Log messages above this level (debug, *info, warn, error)

  • --host= - The external IP (deprecated)

  • --port= - The port to listen on

  • --daemon - Enable or disable daemon mode. 1 for yes, 0 for no.

  • --svcctl= - Windows service management (--svcctl="install" or --svcctl="remove")

  • --service - Use system folders (/var/run/i2pd.pid, /var/log/i2pd.log, /var/lib/i2pd).

  • --ipv6 - Enable communication through ipv6, off by default

  • --notransit - Router will not accept transit tunnels at startup. 0 by default

  • --floodfill - Router will be floodfill, off by default

  • --bandwidth= - L if bandwidth is limited to 32Kbs/sec, O - to 256Kbs/sec, P - unlimited This option will be ignored if --floodfill given

  • --http.address= - The address to listen on (HTTP server)

  • --http.port= - The port to listen on (HTTP server)

  • --httpproxy.address= - The address to listen on (HTTP Proxy)

  • --httpproxy.port= - The port to listen on (HTTP Proxy) 4446 by default

  • --httpproxy.keys= - optional keys file for proxy local destination (both HTTP and SOCKS)

  • --socksproxy.address= - The address to listen on (SOCKS Proxy)

  • --socksproxy.port= - The port to listen on (SOCKS Proxy). 4447 by default

  • --socksproxy.keys= - optional keys file for proxy local destination (both HTTP and SOCKS)

  • --socksproxy.outproxy= - Address of outproxy. requests outside i2p will go there

  • --socksproxy.outproxyport= - Outproxy remote port

  • --sam.address= - The address to listen on (SAM bridge)

  • --sam.port= - Port of SAM bridge. Usually 7656. SAM is off if not specified

  • --bob.address= - The address to listen on (BOB command channel)

  • --bob.port= - Port of BOB command channel. Usually 2827. BOB is off if not specified

  • --i2pcontrol.address= - The address to listen on (I2P control service)

  • --i2pcontrol.port= - Port of I2P control service. Usually 7650. I2PControl is off if not specified

Config files

INI-like, syntax is the following : = . Comments are "#", not ";" as you may expect. See boost ticket All command-line parameters are allowed as keys, but note for those which contains dot (.).

For example:

i2p.conf:

# comment
log = yes
ipv6 = yes
# settings for specific module
[httpproxy]
port = 4444
# ^^ this will be --httproxy.port= in cmdline
# another one
[sam]
enabled = yes

tunnels.cfg (filename of this config is subject of change):

# outgoing tunnel sample, to remote service
# mandatory parameters:
# * type -- always "client"
# * port -- local port to listen to
# * destination -- i2p hostname
# optional parameters (may be omitted)
# * keys -- our identity, if unset, will be generated on every startup,
#     if set and file missing, keys will be generated and placed to this file
# * address -- local interface to bind
# * signaturetype -- signature type for new destination. 0,1 or 7
[IRC]
type = client
address = 127.0.0.1
port = 6668
destination = irc.postman.i2p
keys = irc-keys.dat
#
# incoming tunnel sample, for local service
# mandatory parameters:
# * type -- always "server"
# * host -- ip address of our service
# * port -- port of our service
# * keys -- file with LeaseSet of address in i2p
# optional parameters (may be omitted)
# * inport -- optional, i2p service port, if unset - the same as 'port'
# * accesslist -- comma-separated list of i2p addresses, allowed to connect
#    every address is b32 without '.b32.i2p' part
[LOCALSITE]
type = server
host = 127.0.0.1
port = 80
keys = site-keys.dat
inport = 81
accesslist = <b32>[,<b32>]

Also see this page for more tunnel examples.