I2P: End-to-End encrypted and anonymous Internet https://i2pd.website/
You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.

87 lines
4.1 KiB

i2pd configuration
==================
Command line options
--------------------
* --host= - The external IP (deprecated).
* --port= - The port to listen on
* --httpaddress= - The address to listen on (HTTP server)
* --httpport= - The port to listen on (HTTP server)
* --log= - Enable or disable logging to file. 1 for yes, 0 for no.
* --loglevel= - Log messages above this level (debug, *info, warn, error)
* --pidfile= - Where to write pidfile (dont write by default)
* --daemon= - Enable or disable daemon mode. 1 for yes, 0 for no.
* --svcctl= - Windows service management (--svcctl="install" or --svcctl="remove")
* --service= - 1 if uses system folders (/var/run/i2pd.pid, /var/log/i2pd.log, /var/lib/i2pd).
* --v6= - 1 if supports communication through ipv6, off by default
* --floodfill= - 1 if router is floodfill, off by default
* --bandwidth= - L if bandwidth is limited to 32Kbs/sec, O - to 256Kbs/sec, P - unlimited
* --notransit= - 1 if router doesn't accept transit tunnels at startup. 0 by default
* --httpproxyaddress= - The address to listen on (HTTP Proxy)
* --httpproxyport= - The port to listen on (HTTP Proxy) 4446 by default
* --socksproxyaddress= - The address to listen on (SOCKS Proxy)
* --socksproxyport= - The port to listen on (SOCKS Proxy). 4447 by default
* --proxykeys= - optional keys file for proxy local destination (both HTTP and SOCKS)
* --samaddress= - The address to listen on (SAM bridge)
* --samport= - Port of SAM bridge. Usually 7656. SAM is off if not specified
* --bobaddress= - The address to listen on (BOB command channel)
* --bobport= - Port of BOB command channel. Usually 2827. BOB is off if not specified
* --i2pcontroladdress= - The address to listen on (I2P control service)
* --i2pcontrolport= - Port of I2P control service. Usually 7650. I2PControl is off if not specified
* --tunnelscfg= - Tunnels Config file (default: ~/.i2pd/tunnels.cfg or /var/lib/i2pd/tunnels.cfg)
* --conf= - Config file (default: ~/.i2pd/i2p.conf or /var/lib/i2pd/i2p.conf)
This parameter will be silently ignored if the specified config file does not exist.
Options specified on the command line take precedence over those in the config file.
Config files
------------
INI-like, syntax is the following : <key> = <value>.
Comments are "#", not ";" as you may expect. See [boost ticket](https://svn.boost.org/trac/boost/ticket/808)
All command-line parameters are allowed as keys, for example:
i2p.conf:
log = 1
v6 = 0
tunnels.cfg (filename of this config is subject of change):
# outgoing tunnel sample, to remote service
# mandatory parameters:
# * type -- always "client"
# * port -- local port to listen to
# * destination -- i2p hostname
# optional parameters (may be omitted)
# * keys -- our identity, if unset, will be generated on every startup,
# if set and file missing, keys will be generated and placed to this file
9 years ago
# * address -- local interface to bind
# * signaturetype -- signature type for new destination. 0,1 or 7
[IRC]
type = client
9 years ago
address = 127.0.0.1
port = 6668
destination = irc.postman.i2p
keys = irc-keys.dat
#
# incoming tunnel sample, for local service
# mandatory parameters:
# * type -- always "server"
# * host -- ip address of our service
# * port -- port of our service
# * keys -- file with LeaseSet of address in i2p
# optional parameters (may be omitted)
# * inport -- optional, i2p service port, if unset - the same as 'port'
# * accesslist -- comma-separated list of i2p addresses, allowed to connect
# every address is b32 without '.b32.i2p' part
[LOCALSITE]
type = server
host = 127.0.0.1
port = 80
keys = site-keys.dat
inport = 81
accesslist = <b32>[,<b32>]
Also see [this page](https://github.com/PurpleI2P/i2pd/wiki/tunnels.cfg) for more tunnel examples.