mirror of https://github.com/GOSTSec/sgminer
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
54 lines
3.2 KiB
54 lines
3.2 KiB
|
|
This README contains extended details about FPGA mining with cgminer |
|
|
|
|
|
Icarus |
|
|
|
There is a hidden option in cgminer when Icarus support is compiled in: |
|
|
|
--icarus-timing <arg> Set how the Icarus timing is calculated - one setting/value for all or comma separated |
|
default Use the default Icarus hash time (2.6316ns) |
|
short Calculate the hash time and stop adjusting it at ~315 difficulty 1 shares (~1hr) |
|
long Re-calculate the hash time continuously |
|
value Specify the hash time in nanoseconds (e.g. 2.6316) |
|
|
|
Icarus timing is required for devices that do not exactly match a default Icarus Rev3 in |
|
processing speed |
|
If you have an Icarus Rev3 you should not norally need to use --icarus-timing since the |
|
default values will maximise the MH/s and display it correctly |
|
|
|
Icarus timing is used to determine the number of hashes that have been checked when it aborts |
|
a nonce range (including on a LongPoll) |
|
It is also used to determine the elapsed time when it should abort a nonce range to avoid |
|
letting the Icarus go idle, but also to safely maximise that time |
|
|
|
'short' or 'long' mode should only be used on a computer that has enough CPU available to run |
|
cgminer without any CPU delays (an active desktop or swapping computer would not be stable enough) |
|
Any CPU delays while calculating the hash time will affect the result |
|
'short' mode only requires the computer to be stable until it has completed ~315 difficulty 1 shares |
|
'long' mode requires it to always be stable to ensure accuracy, however, over time it continually |
|
corrects itself |
|
|
|
When in 'short' or 'long' mode, it will report the hash time value each time it is re-calculated |
|
In 'short' or 'long' mode, the scan abort time starts at 5 seconds and uses the default 2.6316ns |
|
scan hash time, for the first 5 nonce's or one minute (whichever is longer) |
|
|
|
In 'default' or 'value' mode the 'constants' are calculated once at the start, based on the default |
|
value or the value specified |
|
|
|
To determine the hash time value for a non Icarus Rev3 device or an Icarus Rev3 with a different |
|
bitstream to the default one, use 'long' mode and give it at least a few hundred shares, or use |
|
'short' mode and take note of the final hash time value (Hs) calculated |
|
You can also use the RPC API 'stats' command to see the current hash time (Hs) at any time |
|
|
|
The Icarus code currently only works with a dual FPGA device that supports the same commands as |
|
Icarus Rev3 requires and also is less than ~840MH/s and greater than 2MH/s |
|
If a dual FPGA device does hash faster than ~840MH/s it should work correctly if you supply the |
|
correct hash time nanoseconds value |
|
|
|
The timing code itself will affect the Icarus performance since it increases the delay after |
|
work is completed or aborted until it starts again |
|
The increase is, however, extremely small and the actual increase is reported with the |
|
RPC API 'stats' command (a very slow CPU will make it more noticeable) |
|
Using the 'short' mode will remove this delay after 'short' mode completes |
|
The delay doesn't affect the calculation of the correct hash time
|
|
|