While BTC donations are preferred, if you wish to donate to the author, Con Kolivas, in LTC, please submit your donations to: Lc8TWMiKM7gRUrG8VB8pPNP1Yvt1SGZnoH Otherwise, please donate in BTC as per the main README. --- Scrypt mining, AKA litecoin mining, for GPU is completely different to sha256 used for bitcoin mining. The algorithm was originally developed in a manner that it was anticipated would make it suitable for mining on CPU but NOT GPU. Thanks to some innovative work by Artforz and mtrlt, this was proven to be wrong. However, it has very different requirements to bitcoin mining and is a lot more complicated to get working well. Note that it is a ram dependent workload, and requires you to have enough system ram as well as fast enough GPU ram. If you have less system ram than your GPU has, it may not be possible to mine at any reasonable rate. There are 5 main parameters to tuning scrypt, all of which are optional for further fine tuning. When you start mining, cgminer may fail IN RANDOM WAYS. They are all due to parameters being outside what the GPU can cope with. NOTE that if it does not fail at startup, the presence of hardware errors (HW) are a sure sign that you have set the parameters too high. DRIVERS AND OPENCL SDK The choice of driver version for your GPU is critical, as some are known to break scrypt mining entirely while others give poor hashrates. As for the OpenCL SDK installed, for AMD it must be version 2.6 or later. Step 1 on Linux: export GPU_MAX_ALLOC_PERCENT=100 If you do not do this, you may find it impossible to scrypt mine. You may find a value of 40 is enough and increasing this further has little effect. export GPU_USE_SYNC_OBJECTS=1 may help CPU usage a little as well. On windows the same commands can be passed via a batch file if the following lines are in the .bat before starting cgminer: setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 --intensity XX (-I XX) The scale goes from 0 to 42. The reason this is crucial is that too high an intensity can actually be disastrous with scrypt because it CAN run out of ram. High intensities start writing over the same ram and it is highly dependent on the GPU, but they can start actually DECREASING your hashrate, or even worse, start producing garbage with HW errors skyrocketing, or locking up the system altogether. Note that if you do NOT specify an intensity, cgminer uses dynamic mode which is designed to minimise the harm to a running desktop and performance WILL be poor. The lower limit to intensity with scrypt is usually 8 and cgminer will prevent it going too low. SUMMARY: Setting this for reasonable hashrates is mandatory. --shaders XXX is an option where you tell cgminer how many shaders your GPU has. This helps cgminer try to choose some meaningful baseline parameters. Use this table below to determine how many shaders your GPU has, and note that there are some variants of these cards, and nvidia shaders are much much lower and virtually pointless trying to mine on. If this is not set, cgminer will query the device for how much memory it supports and will try to set a value based on that. SUMMARY: This will get you started but fine tuning for optimal performance is required. Using --thread-concurrency is recommended instead. GPU Shaders 7750 512 7770 640 7850 1024 7870 1280 7950 1792 7970 2048 6850 960 6870 1120 6950 1408 6970 1536 6990 (6970x2) 6570 480 6670 480 6790 800 6450 160 5670 400 5750 720 5770 800 5830 1120 5850 1440 5870 1600 5970 (5870x2) These are only used as a rough guide for cgminer, and it is rare that this is all you will need to set. Optional parameters to tune: -g, --thread-concurrency, --lookup-gap --thread-concurrency: This tunes the optimal size of work that scrypt can do. It is internally tuned by cgminer to be the highest reasonable multiple of shaders that it can allocate on your GPU. Ideally it should be a multiple of your shader count. vliw5 architecture (R5XXX) would be best at 5x shaders, while VLIW4 (R6xxx and R7xxx) are best at 4x. Setting thread concurrency overrides anything you put into --shaders and is ultimately a BETTER way to tune performance. SUMMARY: Spend lots of time finding the highest value that your device likes and increases hashrate. -g: Once you have found the optimal shaders and intensity, you can start increasing the -g value till cgminer fails to start. This is really only of value if you want to run low intensities as you will be unable to run more than 1. SUMMARY: Don't touch this. --lookup-gap This tunes a compromise between ram usage and performance. Performance peaks at a gap of 2, but increasing the gap can save you some GPU ram, but almost always at the cost of significant loss of hashrate. Setting lookup gap overrides the default of 2, but cgminer will use the --shaders value to choose a thread-concurrency if you haven't chosen one. SUMMARY: Don't touch this. Related parameters: --worksize XX (-w XX) Has a minor effect, should be a multiple of 64 up to 256 maximum. SUMMARY: Worth playing with once everything else has been tried but will probably do nothing. --vectors XX (-v XX) Vectors are NOT used by the scrypt mining kernel. SUMMARY: Does nothing. Overclocking for scrypt mining: First of all, do not underclock your memory initially. Scrypt mining requires memory speed and on most, but not all, GPUs, lowering memory speed lowers mining performance. Second, absolute engine clock speeds do NOT correlate with hashrate. The ratio of engine clock speed to memory matters, so if you set your memory to the default value, and then start overclocking as you are running it, you should find a sweet spot where the hashrate peaks and then it might actually drop if you increase the engine clock speed further. Third, the combination of motherboard, CPU and system ram ALSO makes a difference, so values that work for a GPU on one system may not work for the same GPU on a different system. A decent amount of system ram is actually required for scrypt mining, and 4GB is suggested. Finally, the power consumption while mining at high engine clocks, very high memory clocks can be far in excess of what you might imagine. For example, a 7970 running with the following settings: --thread-concurrency 22392 --gpu-engine 1135 --gpu-memclock 1890 was using 305W! --- TUNING AN AMD RADEON 7970 Example tuning a 7970 for Scrypt mining: On linux run this command: export GPU_MAX_ALLOC_PERCENT=100 or on windows this: setx GPU_MAX_ALLOC_PERCENT 100 in the same console/bash/dos prompt/bat file/whatever you want to call it, before running cgminer. First, find the highest thread concurrency that you can start it at. They should all start at 8192 but some will go up to 3 times that. Don't go too high on the intensity while testing and don't change gpu threads. If you cannot go above 8192, don't fret as you can still get a high hashrate. Delete any .bin files so you're starting from scratch and see what bins get generated. First try without any thread concurrency or even shaders, as cgminer will try to find an optimal value cgminer -I 13 If that starts mining, see what bin was generated, it is likely the largest meaningful TC you can set. Starting it on mine I get: scrypt130302Tahitiglg2tc22392w64l8.bin See tc22392 that's telling you what thread concurrency it was. It should start without TC parameters, but you never know. So if it doesn't, start with --thread-concurrency 8192 and add 2048 to it at a time till you find the highest value it will start successfully at. Then start overclocking the eyeballs off your memory, as 7970s are exquisitely sensitive to memory speed and amazingly overclockable but please make sure it keeps adequately cooled with --auto-fan! Do it while it's running from the GPU menu. Go up by 25 at a time every 30 seconds or so until your GPU crashes. Then reboot and start it 25 lower as a rough start. Mine runs stable at 1900 memory without overvolting. Overvolting is the only thing that can actually damage your GPU so I wouldn't recommend it at all. Then once you find the maximum memory clock speed, you need to find the sweet spot engine clock speed that matches it. It's a fine line where one more MHz will make the hashrate drop by 20%. It's somewhere in the .57 - 0.6 ratio range. Start your engine clock speed at half your memory clock speed and then increase it by 5 at a time. The hashrate should climb a little each rise in engine speed and then suddenly drop above a certain value. Decrease it by 1 then until you find it climbs dramatically. If your engine clock speed cannot get that high without crashing the GPU, you will have to use a lower memclock. Then, and only then, bother trying to increase intensity further. My final settings were: --gpu-engine 1141 --gpu-memclock 1875 -I 20 for a hashrate of 745kH. Note I did not bother setting a thread concurrency. Once you have the magic endpoint, look at what tc was chosen by the bin file generated and then hard code that in next time (eg --thread-concurrency 22392) as slight changes in thread concurrency will happen every time if you don't specify one, and the tc to clock ratios are critical! Good luck, and if this doesn't work for you, well same old magic discussion applies, I cannot debug every hardware combo out there. Your numbers will be your numbers depending on your hardware combination and OS, so don't expect to get exactly the same results! --- While BTC donations are preferred, if you wish to donate to the author, Con Kolivas, in LTC, please submit your donations to: Lc8TWMiKM7gRUrG8VB8pPNP1Yvt1SGZnoH Otherwise, please donate in BTC as per the main README.