- API new commands enablepool and disablepool (version already incremented)
- Tolerate new-format temperature readings
- Modify cgminer.c pool control to allow API to call it
- Bugfix: Fix BitFORCE driver memory leak in debug logging
- Extra byte was being unused and leading to failure on some platforms.
- Explicitly type the constants in poclbm kernel as uint.
- Don't save 'include' when saving the configuration
- Allow configuration file to include another recursively
- Use the SDK and hardware information to choose good performing default
kernels.
- Move phatk kernel to offset vector based nonce bases as well.
- Add a --benchmark feature which works on a fake item indefinitely to compare
device performance without any server or networking influence.
- Allow writing of multiple worksizes to the configuration file.
- Allow writing of multiple vector sizes to the configuration file.
- Allow writing of multiple kernels to the configuration file.
- Allow multiple different kernels to be chosen per device.
- Allow the worksize to be set per-device.
- Allow different vectors to be set per device.
- If we're well below the target temperature, increase gpu engine speed back to
maximum in case we have gotten lost between profiles during an idle period.
- We should be setting the value of fan_optimal, not its address.
- As all kernels will be new versions it's an opportunity to change the .bin
format and make it simpler. Specifying bitalign is redundant and long can be l.
- Use any() in kernel output code.
- Put the nonce for each vector offset in advance, avoiding one extra addition
in the kernel.
- Reset times after all mining threads are started to make estimating hashrates
easier at startup.
- Bugfix: allow no-exec (NX) stack
- Fix minor warning.
- fix the bitforce.c code style follow 1TBS
- fix icarus.c compile warning
- small changes to speedup no vec for AMD 898.1 OCL runtime
- Update licensing to GPL V3.
- Reset the longpoll flag after it's been used once to prevent it restarting
work again.
- Begin import of DiabloMiner kernel.
- Modify API debug messages to say API instead of DBG
- When API shuts down cgminer don't kill itself
- Don't make rolled work from the longpoll be seen as other longpoll work items.
- API add 'privileged' command so can verify access level
- Set the lp_sent variable under lock since there will almost always be a race
on setting this variable, potentially leading to multiple LPs being sent out.
- API restrict access to all non display commands by default
- Update API version to 1.2 for new 'Log Interval'
- API add --log Interval to 'config' reply
- --api-allow special case 0/0 means all
Version 2.2.7 - February 20, 2012
- Send out extra longpolls when we have switched pools and the longpoll thread
@ -8,10 +60,10 @@ high reject rates on failover.
@@ -8,10 +60,10 @@ high reject rates on failover.
and use it to help determine block changes directly from the work longpoll bool.
- Keep track of when a longpoll has been sent for a pool and if the current pool
is requesting work but has not sent a longpoll request, convert one of the work
i
items to a longpoll.
- Store the longpoll url in the pool struct and update it from the pool_active
test in case it changes. This is to allow further changes to longpoll management
on
on switching pools.
- Re-check for a longpoll supporting pool every 30 seconds if none is found
initially.
- Report threads as busy waiting on getwork on startup to avoid them being
@ -29,7 +81,7 @@ on startup instead of with each device initialisation.
@@ -29,7 +81,7 @@ on startup instead of with each device initialisation.
can fail for many reasons.
- Keep track of intended engine clock speed and only adjust up if it's higher
than the last intended speed. This avoids setting the clock speed to one
relative to
relative to a lower profile one by mistake.
- Use gpu-memdiff on startup if an engine clockspeed is set and a memdiff value
is set.
- Revert "Adjust engine speed up according to performance level engine setting,
@ -41,7 +93,7 @@ them trying to start up again with saved pings in their queues.
@@ -41,7 +93,7 @@ them trying to start up again with saved pings in their queues.
before refresh.
- Curses will be disabled in clean_up so don't do it early in kill_work, and
disable_adl so that GPU settings may be restored to normal in case shutting down
curs
curses leads to instability on windows.
- Stop the mining threads before trying to kill them.
- Plain refresh() does not give reliably screen updates so get rid of all uses
Con Kolivas
13 years ago